suction inlet
英 [ˈsʌkʃn ˈɪnlet]
美 [ˈsʌkʃn ˈɪnlet]
网络 吸入口
双语例句
- Margin waste suction inlet in lower suction method, computerized automatic positioning. RECOVERY OF Cu FROM ACIDIC COPPER RINSE WATER
纸边废纸吸入口采下吸式.电脑自动定位.槽边循环电解法从酸性镀铜废水中回收铜 - Margin waste suction inlet in lower suction method, computerized automatic positioning.
机舱应急舱底水吸入口纸边废纸吸入口采下吸式.电脑自动定位。 - The sucking room is provided on the bellmouthing end of the reducing pipe, another end of the sucking room is a suction inlet.
吸入室安装在异径管的喇叭口端，吸入室的另一端为吸入口。 - The vaporized refrigerant vapor from the low temperature and low pressure, suction inlet of the compressor to be compressed, compressed and then discharged into the next cycle.
蒸发后的低温低压冷媒蒸气，从压缩机的吸气口流回，被压缩压缩后排出进入下一循环。 - To reduce resistance from the suction section of pump, the water pump must be installed at the condenser inlet of air conditioner.
为减小泵的吸入段阻力，水泵必须装在空调机冷凝器进口。 - Impact of suction position on starting of hypersonic inlet
抽吸位置对高超声速进气道起动性能的影响 - Vapor-liquid heat exchangers are often used to superheat the suction vapor of compressor and to subcool the inlet liquid of throttle valves in refrigerating system.
制冷循环中往往采用回热器，使压缩机吸气过热和膨胀阀入口液体过冷。 - The hydraulic analysis of pump for suction penetration of bucket foundation as well as the pressure head relation between bucket cavity and pump inlet for different water depths and different pump mounting heights are described in this paper.
对桶形基础平台负压沉贯过程中汲水泵机进行了初步水力分析，讨论了不同水深、不同泵机安装高度情况下，桶腔和泵机进口之间的压头关系。 - The optimized structure of the separators was obtained by analyzing the numerical simulation result, and the influences of suction velocity on the flow field and particle separation was analyzed by changing the inlet parameter of the separators.
分析数值模拟结果得到了内置组合式高温旋涡分离器的优化结构，并通过改变分离器入口参数，分析了入口速度对流场及颗粒分离的影响。 - At the larger mass flow, the relative velocity at the middle channel was higher than that both of suction side and pressure side of the impeller at the inlet section.
流量大于设计流量时，在流道入口段中线附近区域流体的相对速度较大，压力面和吸力面附近流体的相对速度均较小； - Therefore, a gas-separator is to be fitted in front of the suction inlet for the submersible pump, and its running properties are to be improved.
为此，在泵吸入口前增设一油气分离器，从而改善了潜油泵的运行性能。 - New forming process on the suction inlet of large-size electric motors as well as its raw materials dimension and mold construction is introduced.
介绍了大型电机吸风嘴成型工艺、坯料尺寸确定及模具结构。 - Analysis of Suction Roles for Supersonic Inlet on Combined Engine
某组合发动机进气道抽吸作用分析 - The design of the pump suction sump will influence the running efficiency and security performance. In this new pump suction sump, there are three special design characters: closed structure, double inlet and double track structure, and transition plane structure.
水泵吸水池设计的合理与否，会直接影响到泵站的运行效率和安全，在新型水泵吸水池设计中采用了三种结构形式：封闭式池身结构、双进口双流道结构和倒角过渡结构。 - The shape of the suction chamber decides the inlet velocity distribution of the compression grade in the multiphase pump, and affects the performance of the multiphase pump to a degree.
吸入室的形状决定了混输泵的压缩级进口的速度分布，对混输泵的性能有一定的影响。 - The suction facilities include the pipeline from the suction fluid surface to the inlet of the pump and valves and fittings.
吸入装置包括吸入液面至泵进口处的管路、阀件等。 - New Forming Process on the Suction Inlet of Large-size Electric Motors
大型电机吸风嘴成型新工艺 - On the pressure surface and suction surface, three dimensional flow area of the large-enthalpy drop static blades and rotor blades have certain extent decreases as the inlet Mach number is increasing, which restrains the annular-cascade secondary flow in a certain extent.
进口马赫数的增大使大焓降静叶和动叶的压力面和吸力面的三维流动区有一定幅度的减小，在一定程度上抑制了叶栅内的二次流动。